Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - modellius

Pages: 1 ... 150 151 [152] 153 154 155
Warplane Art / Re: Grumman Intruder and Prowler
« on: March 08, 2014, 07:24:37 PM »
no comment  :-clap :-clap :-clap :-clap

Aircraft Modeling / Re: MiG-21R
« on: March 08, 2014, 07:23:05 PM »
nice !

Aircraft Modeling / Re: Ryan ST Series
« on: March 04, 2014, 10:33:30 PM »
very nice build, very long  :-green but very nice !

Aircraft Modeling / Re: Eduard Bf 110
« on: March 03, 2014, 12:16:16 PM »
The cockpit is finally finished, moving to conopy, and getting one step closer to finish the model.

Of course, a bit of body work is still needed to get the airplane right.

A bit of advice, it's better to cut off the barrels of the mg and put it on safe place, the brassin is too easy to brake, and if you brake it ( and you will, trust me ) it's very possible you will never find those barrels again.....

Aircraft Modeling / Re: MiG-21R
« on: March 02, 2014, 11:54:38 PM »
so far so good !

Aircraft Modeling / Re: Eduard Bf 110
« on: February 27, 2014, 10:27:26 AM »
Hellooo boys, I'm baaaaaaaack !  :)

I made a test spraying with gunze mr surfacer to see is there any places needed a little more fixing, well, of course there was, but in the meantime these problems are fixed, hope I will a paint soon, more pictures too come !  :-wave

Aircraft Modeling / Re: MiG-15bis Eduard 1/72
« on: February 25, 2014, 07:41:48 PM »
Nice !

Aircraft Modeling / Re: Jumo Powered Bf-109s In 1/48
« on: February 25, 2014, 07:40:59 PM »

Very nice, like it a lot !

Aircraft Modeling / Re: MiG-21R
« on: February 25, 2014, 07:38:30 PM »
Looking forward for more !

Aircraft Modeling / Re: Rafale C "Tigermeet 2013"
« on: January 16, 2014, 08:12:28 PM »
very nice !

Aircraft Modeling / Re: A7 E Corsair II
« on: January 14, 2014, 03:38:37 PM »
And the work continued..... Aires way to replace the kits part is not a good idea, I think it can't be done on that way and to look as it should, so I had to remove almost half of the kit and rebuild it from styrene and use the aires replacement parts as the starting point. Of course lots of details lost....

The intake is complicated as much as possible, it has two halves, longitudinally, lots of putty and sanding on a very inaccessible place, not to mention the bad connection of the intake with the fuselage. Here the only upgrade I made is the cutting of the hasegawas inake end and made a new one from styrene and some p.e leftover to simulate the first row of the blades of the engine, becouse of the size of the intake it will be visible

Aircraft Modeling / Re: Eduard Bf 110
« on: January 14, 2014, 03:04:07 PM »
The work continued, some more putty, and sanding.....However, I completed the wings and must say all the parts fits in just perfectly. Replacing all the lost details is in progress, hope I will paint very soon  :-think

Aircraft Modeling / Re: A7 E Corsair II
« on: December 30, 2013, 01:58:56 PM »
90% finished seat

Aircraft Modeling / Re: Eduard Bf 110
« on: December 30, 2013, 01:37:15 PM »
The work continued. The gap on the rear of the engine units, behind the main wheel bays wasn't even so I had to fix it with a saw and some putty.

The first serious problem is the joining of the wing section with the fuselage. The resin cockpit " sits " too low in the fuselage so I couldn't fit it nicely despite the sanding the cockpit floor to the maximum. lots of putty and sand-papering needed on this one. Unfortunately there will be lots of lost details to recover.....

Pages: 1 ... 150 151 [152] 153 154 155