841
Combat Warplanes / Re: MiG-29
« on: May 16, 2021, 07:23:50 PM »
Flights in the 39th Air Force Brigade. Zhytomyr region, Ozernoye, Ukraina
News:
Forum is closed for new members. All content is private and can not be shared
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
845
Aircraft Modeling / Re: Messerschmitt BF 109Z (RetroWings 1/72)
« on: May 13, 2021, 09:01:54 PM »
Hope all of this surgery will not be visible once when painted 
846
Combat Warplanes / Re: Fokker D.XI
« on: May 13, 2021, 09:00:53 PM »
With grass and flowers could be gift to wife too 
847
Aircraft Modeling / Re: Azur Savoia Marchetti SM 79 JIS/JRS B, 1/72
« on: May 13, 2021, 08:59:51 PM »
Thanks
848
Combat Warplanes / F-15
« on: May 13, 2021, 02:40:11 PM »
Preparation of F-15I fighters of the Israeli Air Force for bomb mission in the Gaza.
849
Aircraft Modeling / Re: Azur Savoia Marchetti SM 79 JIS/JRS B, 1/72
« on: May 07, 2021, 04:41:54 PM »
This is situation in the moment and must stop for a while as well I have no cement anymore... need to make order...
850
Combat Warplanes / Fokker D.XI
« on: May 05, 2021, 04:35:35 PM »
After moving to the Netherlands, Fokker continued to develop fighter aircraft. Despite the fact that the V. IX and D.X projects were not successful, the designer Reinold Platz (Reinhold Platz) in 1923 began work on a new aircraft D.XI
Built in 1921, the D. IX fighter became the basis for the D. XI. It was a single-seat sesquiplane with a non-retractable landing gear. The 300 hp Hispano-Suiza 8 Fb engine could reach speeds of up to 225 km / h. The flight range was 440 km. Armament — 2 × 7.7 mm machine guns.
According to its characteristics, the Fokker D. XI was one of the best fighters of its time. But financial problems prevented the Dutch government from ordering these planes. Therefore, all 117 produced D. XI fighters went for export — to the USSR, Romania, Spain, Switzerland, Argentina and the United States.
Built in 1921, the D. IX fighter became the basis for the D. XI. It was a single-seat sesquiplane with a non-retractable landing gear. The 300 hp Hispano-Suiza 8 Fb engine could reach speeds of up to 225 km / h. The flight range was 440 km. Armament — 2 × 7.7 mm machine guns.
According to its characteristics, the Fokker D. XI was one of the best fighters of its time. But financial problems prevented the Dutch government from ordering these planes. Therefore, all 117 produced D. XI fighters went for export — to the USSR, Romania, Spain, Switzerland, Argentina and the United States.
851
Warplane Art / Re: Fokker B.I
« on: May 03, 2021, 04:19:58 PM »
Nice story and very rare subject!! Thank you 
852
Aircraft Modeling / Re: Azur Savoia Marchetti SM 79 JIS/JRS B, 1/72
« on: May 01, 2021, 05:59:34 PM »
853
Aircraft Modeling / Re: Azur Savoia Marchetti SM 79 JIS/JRS B, 1/72
« on: May 01, 2021, 04:06:01 PM »
Here is situation in the moment- fuselage is joined without any difficulties and half's fit perfect. Note that it does not include any kind of pins and holes, but need to be adjusted by hands. Join area is in first moment just roughly sanded and later, when I add wings, tail surfaces and cockpit elements, will add some filler and sand it all over with fine sanding paper. Nose is consist from two half's and as well windows frames are so tiny, need maximum attention with cement use. Wings are not complicated, few plates at inner side of top wing surfaces and then all merged together.
Extra work need to fit wings of fuselage. Problem is that wing sleeve is not good and when push wing into that position, you have negative dihedral on wings. Top wing surface on SM 79 series need to be 0 degrees and to achieve that, much of the wing sleeve's need to be sanded, maybe even one mm each side. Final problem which appeared is that surfaces did not match (wing and fuselage bottom), so I need one clamp to make it in level and hold it till cement harden.
Extra work need to fit wings of fuselage. Problem is that wing sleeve is not good and when push wing into that position, you have negative dihedral on wings. Top wing surface on SM 79 series need to be 0 degrees and to achieve that, much of the wing sleeve's need to be sanded, maybe even one mm each side. Final problem which appeared is that surfaces did not match (wing and fuselage bottom), so I need one clamp to make it in level and hold it till cement harden.