Messages

2371

Aircraft Modeling / Re: Eduard Bf 110

« on: February 27, 2014, 10:27:26 AM »

Hellooo boys, I'm baaaaaaaack ! 

I made a test spraying with gunze mr surfacer to see is there any places needed a little more fixing, well, of course there was, but in the meantime these problems are fixed, hope I will a paint soon, more pictures too come ! 

2372

Aircraft Modeling / Re: MiG-15bis Eduard 1/72

« on: February 25, 2014, 07:41:48 PM »

Nice !

2373

Aircraft Modeling / Re: Jumo Powered Bf-109s In 1/48

« on: February 25, 2014, 07:40:59 PM »

 

2374

Aircraft Modeling / Re: Hawker Hurricane MK I "Fabric wings" - Belgian Aé. Mil.

« on: February 25, 2014, 07:39:21 PM »

Very nice, like it a lot !

2375

Aircraft Modeling / Re: MiG-21R

« on: February 25, 2014, 07:38:30 PM »

Looking forward for more !

2376

Aircraft Modeling / Re: Rafale C "Tigermeet 2013"

« on: January 16, 2014, 08:12:28 PM »

very nice !

2377

Aircraft Modeling / Re: A7 E Corsair II

« on: January 14, 2014, 03:38:37 PM »

And the work continued..... Aires way to replace the kits part is not a good idea, I think it can't be done on that way and to look as it should, so I had to remove almost half of the kit and rebuild it from styrene and use the aires replacement parts as the starting point. Of course lots of details lost....

The intake is complicated as much as possible, it has two halves, longitudinally, lots of putty and sanding on a very inaccessible place, not to mention the bad connection of the intake with the fuselage. Here the only upgrade I made is the cutting of the hasegawas inake end and made a new one from styrene and some p.e leftover to simulate the first row of the blades of the engine, becouse of the size of the intake it will be visible

2378

Aircraft Modeling / Re: Eduard Bf 110

« on: January 14, 2014, 03:04:07 PM »

The work continued, some more putty, and sanding.....However, I completed the wings and must say all the parts fits in just perfectly. Replacing all the lost details is in progress, hope I will paint very soon 

2379

Aircraft Modeling / Re: A7 E Corsair II

« on: December 30, 2013, 01:58:56 PM »

90% finished seat

2380

Aircraft Modeling / Re: Eduard Bf 110

« on: December 30, 2013, 01:37:15 PM »

The work continued. The gap on the rear of the engine units, behind the main wheel bays wasn't even so I had to fix it with a saw and some putty.

The first serious problem is the joining of the wing section with the fuselage. The resin cockpit " sits " too low in the fuselage so I couldn't fit it nicely despite the sanding the cockpit floor to the maximum. lots of putty and sand-papering needed on this one. Unfortunately there will be lots of lost details to recover.....

2381

Aircraft Modeling / Re: Bf 108 Eduard Weekend Edition

« on: December 28, 2013, 12:24:21 PM »

Looking forward for more !

2382

Aircraft Modeling / Re: A7 E Corsair II

« on: December 26, 2013, 08:27:16 PM »

First the seat. The belts are combined aires from the seat kit and from the eduard p.e. set and of course there is some scrath upgrade with a copper wire and sprue

2383

Aircraft Modeling / Re: A7 E Corsair II

« on: December 24, 2013, 03:37:37 PM »

In the meantime the seat arrived :

And " in-box " review of the other " fun stuff " :

Electronics :

Wheel bays :

The build has begun, photos soon 

2384

Aircraft Modeling / Re: A7 E Corsair II

« on: December 20, 2013, 04:22:16 PM »

Thank you !

2385

Aircraft Modeling / Re: Eduard Bf 110

« on: December 20, 2013, 02:02:08 AM »

After the fuselage I started to work on the wings, wings are perfect assembly the engines are little more problematic and the build of them needs a bit more attention, but it's not too bad

The wing tips fits in perfectly, no putty needed on this one !

The hardest part during the wing build is to install the Brassin part under the wing, needs some extra work a lot of attention but it sure worth it !