LetLetLet ~ Warplanes
Let Let Let - Warplanes => Aircraft Modeling => Topic started by: No.1 on December 14, 2017, 04:57:17 PM
-
This is so impressive kit by its look and final painting is also nice. I have just wanted to start build when I get info about some etched sets available for this kit so I will put this build on stand by. For now just content ;)
-
Nice!
-
Here is the real plane in various colour schemes.
It shows the prototype at the Paris Air Show and the German ILA
-
Aeromacchi logo was so interesting to see :)) thank you Nico :-ok
-
Wake up and go :)) Eduard set prepared for work :))
-
Basic paint with some bras elements
-
Rich content with the PE added!!
-
Yes and parts fit it great. Zvezda plastic is excellent for shaping, remove of some surfaces was so easy before I place etched parts on same place.
-
I loved the few Zvezda kits I've built. Keep going!!
-
Thanks :))
-
As I own that kit, I'm particularily interrested by your build ;)
-
Thank you for attention :)) take great care about every slot, every nut, every bolt of this kit. It is very complex and in same time precise. I use supersonic glue (last photo), which catch parts fast and it work great on Zvezda plastic. I followed instructions strictly and realized that there is no need to place landing gear strut in this work step, will see later is there anything to cover it.
-
Well noted for kit and glue. I will try to find that one in expo here in Belgium...
-
like it a lot !
-
Get one is scale fit to you ;)
-
Here is progress on kit. It is made from subsections and they are merged one by one. Process is demanding as well there is need to precisely capture points where parts need to be set and cemented. What I need to say is that you have to avoid toput ejection seats in cockpit during this work, I have to do that as well I will need that for review of products.
Complex geometry is seen on photo with red circles I put on original photo, previous photo is catured assembly step and it show in what precise point need to be set up part. Any mistake and you would not be able to continue work. Must say again that kit demand use of supersonic gle for plastic as well shape and geometry of kit parts do not easy allow you to use clamps and in many cases even not tape. So you need in many steps to hold parts by your fingers and wait to set up glue. So fast acting glue is on demand.
Must state few things- no matter this kit is released end of last year, not many has been built by modeler. Other thing is mold detoriation during time and distortion of parts, how this kit will be for build in five years?
For now I enjoy it as new experience and for now I must say- not for beginners and not if you are nervous or under stress. In most cases I built kits and drink something... my coffee cool down today and I drink it cold during this work steps.
-
Lot of precision work but what a nice plane...
-
Looks very nice mate !
-
Thanks :))
-
Some of works today, more or less it si close to painting stage
-
Nice!
-
Moving along nicely!
-
Thanks mate :)) now it is ready for painting and I will make sample Yak-130, fuselage number 51, RF-44488, from Borisglebov training aviation center, Russia (Яковлев Як-130 б/н 51, RF-44488, Борисоглебский учебный авиационный центр, Россия)
https://youtu.be/-J64Pt_Uch0
-
One more video from same air base
https://youtu.be/_iln5ggB29g
-
And how it look like in work
-
very good !
-
Thanks!!! Small and cute ;)
-
I LOVE that aircraft!!!
-
Keep on that love ;)
-
Grey!!
-
:-ok
-
so great !
-
Lazy me start work on decals :-razz :-red
-
:-ok
-
Completed :))
-
Looks excellent, well done mate !
-
Thanks :))
-
Splendid!
-
Thanks :))
-
Great work, mate!
-
Thanks :))